Suitable for use: roofs
Effective width: 1100 mm
Tile spacing: 400 mm
Profile height: 45 mm
Thickness of material: 0,45 - 0,50 mm
Coating material: polyester, matte polyester, pural, PVC
Min/max length: 800 / 7500 mm

Price8,40 euro/m2 Buy now

Suitable for use: roofs
Effective width: 1100 mm
Tile spacing: 350 mm
Profile height: 40 mm
Thickness of material: 0,45 - 0,50 mm
Coating material: polyester, matte polyester, pural, PVC
Min/max length: 800 / 7500 mm

Price 7 eur m2 Buy now

Minimum order for goods 100M2

Time for shipping 1-2 Week

Suitable for use: roofs and walls Effective width: 1150 mm Profile height: 18 mm Thickness of material: 0,45 - 0,70 mm Coating material: zinc, polyester, matt polyester, pural, PVC Min/max length: 100 / 10000 mm Price 9.50 eur/ m2 Buy now Minimum order for goods 100M2   Time for shipping 1-2 Week Suitable for use: roofs and walls Effective width: 900 mm Profile height: 45 mm Thickness of material: 0,45 - 0,90 mm Coating material: zinc, polyester, matt polyester, pural, PVC Min/max length: 300 / 10000 mm Price 8,70 eur/ m2 Buy now

RAW MATERIAL The raw material we use is hot-dip zinc-coated steel sheet. The key characteristic indicator of  strength of steel sheet is thickness of its zinc coat, not only thickness of steel blank. The thin steel sheet we offer has a zinc cost 275 – 350 gr/m2  thick. In the course of installation and exploitation, damages to the zinc coat should be avoided, as it leads to rapid corroding of the sheet. To extend the period of use, coated sheet steel is also produced with the zinc layer additionally coated with different colours or plastic finish. These will secure the outward appearance of your roof, facade, rainwater systems etc. and increase their durability for decades. ADVANTAGES OF STEEL ROOF: · Light The steel roof is 10 times lighter than the tiled roof, which is why the substructure does not have to be so massive and expensive. Thus the steel roof is recommended for renovated buildings, where it is not advisable to renovate the substructures. The steel roof, unlike the tiled roof, can be used in the case of a very flat slope! · Fast The profiled tiles are panels measured with precise linear measure and can be installed up to 10 m2 at a time. Therefore it is possible to lay a large surface in a short period of time! · Weather proof The steel roof endures large temperature fluctuations. It is not a porous material and does not allow moss and breaking up as a result of water and ice accumulated in pores. · Paint range Our paint range color allows you to choose between ca 25 different colour shades. · Cheap The steel roof is less expensive due to its quick installation and lighter roofing structure as compared to different other types of roofing. ALLEGED DRAWBACKS OF STEEL ROOFING: · Steel roofs clang Many of our potential clients consider this a drawback of the steel roof. The experience has proved though that the rattle caused by precipitation is irritating in buildings, which lack thermal insulation under the roof, the underlay, floor, i.e. where the steel plate is visible from underneath. We may say that in that case all roofing materials will clang. For dwelling houses, the level of noise caused by precipitation is significantly lower than norm. · Steel roofs are sensitive to storms The corrugated sheeting installed in accordance with the norms (i.e. in the area within 1 m distance from the eaves, ridge and gables, there is compact screw spacing) is not sensitive to any storm or tempest. It is important to have a professional installer do the roofing work! · Steel roofs requires smooth purlins This so to say ”drawback” is true, for the purlins which have not been properly lined up, will cause a wavy roof. It is advisable to use the professional roof installation service!

Impermeability
The roofing cover should be impermeable to all sorts of different conditions. The water gets to he roof in the form of precipitation or brought with the wind blasts during ice storms. In winter, the roofing cover should be protected against the penetration of snow into structures located beneath. Whereas in spring and autumn, it should behave adequately in situations when the cold and thaw alternate. Depending on the type of roofing cover, the impermeability thereof is achieved in two ways: either the cover itself is made completely waterproof or the underlayer is placed under the roofing cover, which drives the absorbed water or condensed water out from under the roofing cover, either into the rainwater system or just into the eaves. A steel roof that has dense surface is the rolled steel roof. The dense cover does not require underlay. The underlay is recommended for tin profiled and corrugated iron sheets covers. See the installation of underlay in greater detail in the installation manuals.

Weather proof
The natural forces alongside UV rays, temperature, rain, snow, wind are hard burden for the roofing coating (especially difficult is the co-effect of rain and wind). The roofing coating should be resistant to the load. Which is why the materials used and the installation work performed, are faced with very high demands. The roof's being weather-proof is achieved through the use of correctly chosen materials and well-considered structures.

Resistance
The roof's coating should be resistant to the blows of branches and other objects tossed by the wind (mechanical factors). Also the repeated drumming of precipitation creates a strong dynamic load. The roofing coat should be resistant to the maintenance work performed on the roof. To facilitate the movement on the roof and to protect the roofing coat, the roofs often ladders and bridges are mounted on the roof. The ever growing air pollution and chemical burden related to that are increasing. The corrosion caused by them affects the roof coating material in a variety of ways. To increase the chemical resistance,  more and more improved methods of processing of raw material are applied.

Maintenance
The roof wears out and grows old just like all the other parts of building. Despite the use of materials increasingly more durable, it is not yet appropriate to talk about “maintenance-free” roof. It is more practical and reasonable to plan regular maintenance activities of the roof to prolong significantly the period of service of the roof. Nonetheless important are practical instructions for removing small defects of the roof.

Appearance
The appearance of the roof depends on the form of the roof, its slope or pitch, material, colours, etc. It has a very important role in creating the overall impression of the building's appearance, and being a part of the entire building and living environment should comply with certain strict rules. The issues related to the roofs are mainly resolved alongside with building facade solutions.

Choice of roof coating.
The roof coating is chosen on the basis of peculiarities of the roof, its slopes, form, etc. This choice affects the possibilities of making the most complicated structures of the roof water-proof. These include, besides joints between sheets, also eaves, inlets, encirclements of ridge and stacks. Not less important is mutual compatibility of rainwater and safety systems with the roof coating. It is important to consider also the peculiarities of installation: some roofs demand a lot of work while others are easily mountable. The most suitable correlation of material and installation price should be established.

How to order a steel roof?
1.First of all you should find out what type of profile is most suitable for a particular type of roof and which you like most. The basic types of profiles are corrugated sheets, tiled profiles and rolled steel profile. For dimensions and drawings of specific profiles see our catalogue of products.
2.Choice of surface coating material. Possibilities: zinc, polyester, matt polyester, pural or PVC. The coating affects the price.
3.Choice of suitable colour. On the basis of these data and precise pre-installation measurements  of the roof, the profile and the need of accessories are calculated. The roofing sheets are cut with precise length. The bevel edge is not definitively cut as in the course of possible measurement errors it may later prove useless. Those cuts are made during installation on the site. Do not use abrasive cutting tools!

To make the volume calculations in case of an uncomplicated roof we need the following dimensions:

Length of ridge

Length of gable

Winch soffit ridge

Winch soffit gable

Length of eaves

For complicated roofs, it is useful, having the available dimensions, to draw all the facets of the roofs separately. If it is easily done, you indeed have all the necessary dimensions. For compiling the price offer, it is enough to submit the design of the building (first and foremost the plan of the roof and the views of the building are important). If an order is made, additional measurements on the site are needed, as dimensions on the drawing often have inaccuracies.

The dimensions are to be submitted by fax, post or in any other way to AS Toode, and do not forget to add your contact data! When transmitting by fax, please avoid using thin and coloured lines, as these will be hardly distinguishable in the fax.